DS/ISO Accuracy (trueness and precision) of measurement methods and results – Part 4: Basic methods for estimating the trueness of a standard. ISO Accuracy (Trueness and Precision) of Measurement Methods and Results – Part 4: Basic Methods for the Determination of the Trueness of a. Buy DS ISO ACCURACY (TRUENESS AND PRECISION) OF MEASUREMENT METHODS AND RESULTS – PART 4: BASIC METHODS FOR.
|Published (Last):||6 January 2017|
|PDF File Size:||13.48 Mb|
|ePub File Size:||7.61 Mb|
|Price:||Free* [*Free Regsitration Required]|
Alternative methods for the determi- nation of the 525-4 of a standard measure- ment method. Basic method for the determination of repeatability and re- producibility of a standard measurement method. A Awar G 1, Reference materials shall be homogeneous. The boxed points in figures B.
The test results for each level are shown in figures B. This implies comparison between the within-laboratory standard deviation and the stated repeatability standard deviation of the standard measurement 7525-4. A guide to decid- ing how many is given below. ISO matallic coatints measurement of coating thickness coulometic method by anodic dissolution. Unless otherwise stated, a is assumed to be 0, Accuracy trueness and precision of measurement methods and results — Part 2: Grundlegendes Verfahren zur Schaetzung der Richtigkeit eines Messverfahrens.
There again, appropriate action should be taken by investigating these laboratories, or, if necessary, by tightening the protocol of the measurement method.
Thus results from each laboratory can be considered as replicates under repeatability conditions. Basic methods for the determination of the trueness of a standard measurement method – Part 5: The laboratory means and vari- ances for each of the five test materials are listed in table 8.
The number of laboratories to be used is discussed in subclause 6. Analytical results 55725-4 percentage Mn Lab.
General principles and definitions. The uncertainty in the estimate of the laboratory bias depends on the repeatability of the measurement method and on the number of test results obtained.
The trueness of the measurement method can be investigated by comparing the accepted reference value with the level of the results given by the measurement method.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. About Us Info center Standardization.
First Balkan IT Conference for business platform for standardization My account Shoping uso 0 Help. Genauigkeit Richtigkeit und Praezision von Messverfahren und Messergebnissen. Comparison of the trueness of two measurement methods is considered in IS0 Methodes de base pour la determination de la justesse d’une methode de mesure normalisee.
In order for the results of an experiment to be able to detect with a high probability see annex Cl a prede- termined magnitude of bias, the minimum number of laboratories, p, and test results, n, shall satisfy the following equation: Accept and continue Learn more about the cookies we use and how to change your settings. It is not applicable if the bias in the measurement of one property is affected by the level of a second property i. If it is proposed to undertake an experiment to estimate laboratory bias, then it should be realized that the estimate will be valid only at the time of the ex- periment.
Bias can arise, for example, in chemical analysis if the measurement method fails to extract all of an element, or if the presence of one element interferes with the determination of another. Intermediate measures of the precision of a standard measurement method.
Do the results of the accuracy experiment justify the acceptability of the measurement method for adoption as a standard? The k values figure B-7 show that laboratories Here B is the laboratory component of bias, i. Worldwide Standards We can source any standard from anywhere in the world.
Utilization of trueness data Refer to clause 7 of IS0 It may appear sio some laboratories did not use the required equipment or did not work ac- cording to the specified conditions. All measurements are to be carried out according to that standard method.
If the repeatability standard deviation, or, of the stan- dard measurement method iwo known, the estimate s, can be assessed by ido following procedure. Methodes de base pour la determination de la justesse d’une methode de mesure normalisee Title in German Genauigkeit Richtigkeit jso Praezision von Messverfahren und Messergebnissen.
Use in practice of accuracy values. IAccuracy trueness and precision of measurement methods and results – Part 1: Further regular testing is required to show that the labora- tory bias does not vary; the method described in IS0 may be used for this.
The h and k values are shown in figures B. There are three cases, as follows. Basic methods for the determination of the trueness of a standard measurement method. When a value for the bias of a measure- ment method is quoted, together with a test result obtained by that method, there is an implication that the same characteristic is being measured in exactly the same way.