Designation: D – 07Standard Guide for Painting Inspectors (Metal Substrates)1 This. Buy ASTM D GUIDE FOR PAINTING INSPECTORS (METAL SUBSTRATES) from SAI Global. ASTM D – Designation: D – 00 Standard Guide for Painting Inspectors (Metal Substrates.
|Published (Last):||20 December 2007|
|PDF File Size:||5.19 Mb|
|ePub File Size:||9.10 Mb|
|Price:||Free* [*Free Regsitration Required]|
Film thickness—wet —dry Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part r3276 the standard.
If it is suspected that the temperature and humidity conditions are such that moisture is condensing upon the surface, measure the relative humidity and dew point as described in Surface cleaning, power tools, and surface pro? Monitoring Standards monitoring is a free service designed for you who wish to be alerted of changes to or new editions of the standards required in your work.
Practice D presents the procedure for evaluating adhesion of maintenance coatings. The contaminants should be removed not simply spread out by a thorough wiping of the affected areas with cloths saturated with clean solvent.
Pressures over KPa 20 psi are needed to achieve total coating removal when using only water. Measurements on relatively rough surfaces, such as a surface blasted to a high pro? Historical Asm s – view previous versions of standard.
Any coating that shows curling, lifting, or wrinkling should be reported to the engineer immediately since it may have to be removed e3276 the area repainted. Steel Structures Painting Council Publications. Storage of Coating and Thinner.
Ear protection Blast Ast Test Methods D and D describe procedures. Some materials may even require constant agitation during use. In another method used primarily in fabricating shop, wheels propel the abrasive centrifugally against the work. If outdoor storage lasts for several months, the inspector should check the integrity of the coating from time to time and verify that de?
A web subscription provides an easy and secure xstm to standards, and you are guaranteed to always have the latest edition. Each has its own safety-related hazards, and U. This ensures that you are always up-to-date and saves you both time and money. Abrasive, dirt, or other debris that becomes embedded in the paint?
Dew point, RH 5.
See Guide D for establishing procedures to certify inspectors for coatings work in nuclear facilities. Product MSD sheets 3. Holiday testing is usually performed on coatings intended for immersion service.
Induction time observed If a pinhole or holiday is present, an electrical circuit is completed and the alarm sounds. Power Tool Cleaning to Bare Metal. Link to Active This link will always route c3276 the current Active version of the standard. Containers should be covered when not in use, to reduce volatile losses and skinning. When a holiday is found, it should be marked, then wiped dry of any moisture to avoid telegraphing back to this holiday.
It consists of a bulletshaped, stainless steel cup with an ori? High humidity can also affect the cure of some coatings.
Only moderate pressure should be used, as heavy pressure can cause foaming and possible cratering by entrapped air. Damaged or bare areas should be thoroughly cleaned, prepared, feathered and repainted with one new coat of shop or? Read more about subscriptions.
The same thermometer or a? Surface Preparation Methods and Requirements. If necessary to remove grime and oil substances, they can be wiped, steam cleaned, power washed with detergents or cleaned with solvents selected so as not to soften the? Asrm cleaning power tools consist of non-woven abrasive wheels and discs, coated abrasive discs or sanding pads, coated abrasive?
Low voltage holiday detectors are suitable on coatings up to aatm In-line heaters are also available for application equipment. Poor spray technique resulting in excessive overspray a sand-like? The coating should not be mixed or kept in suspension by means of an air stream bubbling under the coating surface.
Relative humidity is usually an indicator of condensing conditions and speci? It includes the key elements of d32776 preparation, coatings application, and final approval for both field and shop work. Start Webshop Product catalog Product presentation.
This section describes some commonly accepted procedures when thinning is permitted.