(This document is an excerpt from AISI S North American Standard for Cold Formed Steel Framing – Lateral. Design for convenience only, and should be. Documento 8 – AISI S Standard and Commentary – Committee Use (11!27! 07) – Download as PDF File .pdf), Text File .txt) or read online. AISI S/S ().iv Steel Framing Alliance and the Canadian Sheet Steel Building Institute. North American Standard For Cold-Formed Steel Framing .
|Country:||Antigua & Barbuda|
|Published (Last):||19 October 2006|
|PDF File Size:||11.98 Mb|
|ePub File Size:||16.18 Mb|
|Price:||Free* [*Free Regsitration Required]|
This chapter contains design provisions for cold-formed steel framing members and assemblies, as previously included in AISI S, S, S, and S This method provides an alternative approach to determine the shear wall strength, especially for those that are outside the limitations of the tested systems. Beneficial for the design engineer is a new Effective Strip Method that enables the calculation of the nominal in-plane shear wall strength for Type I shear walls Figure 2.
This new standard includes design provisions for wall systems, floor and roof systems, lateral force-resisting systems, as well as truss and header assemblies.
But, why would AISI develop six discrete framing standards as opposed to one design manual? Section reference table S and previous standard.
The chapter also includes:. Sheathing and discrete bracing. This computational method is applicable for walls sheathed with steel sheet. From tothe AISI Committee on Framing Standards developed nine different framing standards to cover specific aspects of cold-formed steel framing.
The other standards addressed such topics as a code of standard practice, the definition of standard product, and prescriptive design for residential applications. This chapter contains design, manufacturing quality criteria, and installation requirements for cold-formed steel trusses as previously included in AISI S It outlines the scope, which is for design and installation of cold-formed steel framing of a floor and roof systems, b structural walls, c shear walls, strap braced walls, and diaphragms to resist in-plane lateral loads, and d trusses for load-carrying purposes in buildings.
The previous design standards limited their application to framing members having a maximum base steel thickness to mils 0. This has been an often asked question by framing design engineers.
For curtain wall systems, the standard now permits the use of the bracing combination of sheathing attached to one side of the wall stud and discrete bracing for the other flange Figure 1. The truss component structural performance load test and full-scale truss confirmatory test methods, previously included in AISI S, are provided in this appendix.
Effective strip method model for steel-sheet sheathing. The simple reason is, it was s123-07 to develop small single-topic documents versus a more comprehensive multi-topic document.
This chapter provides installation requirements previously contained in the various framing standards. Your message Submit Comment. For roof or floor diaphragms aidi a maximum aspect ratio of 4: Six of these standards addressed the design of structural elements, such as general provisions, wall studs, floor joists, trusses, headers, and shear walls.
Leave a Comment Click here to cancel reply. The ends of a built-up compression member are connected by a weld having a length not less than the maximum width of the member or by connectors spaced longitudinally not more than 4 diameters apart for a distance equal to 1.
The exception applies where the built-up section is seated properly in asii track, and the top and alsi end bearing detail of the studs consists of a steel or concrete support with adequate strength and stiffness to preclude relative end slip of the two built-up stud sections.
However, AISI S now incorporates an exception for a built-up axial load bearing section comprised of two studs oriented back-to-back forming an I-shaped cross-section. First Name Last Name.
The method assumes a sheathing strip carries the lateral load via tension field action. This new chapter lists applicable AISI test standards for cold-formed steel framing members, connections, and systems. Inthe manufacturing tolerance values were extended to the flange width and stiffening lip length. This article focuses on AISI S which applies to cold-formed steel structural members subject to gravity loading, wind loading, and seismic loading, except when specific seismic detailing is required.
The discrete braces are limited to not greater than 8 feet 2. This appendix contains requirements for the determination of the rotational stiffness that structural sheathing provides to framing members to facilitate the design for distortional buckling.
ASTM C has historically stipulated manufacturing tolerances for cold-formed steel structural framing members. Format defines design considerations.